Collapse temperature comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2025-08-20. Where a claim depends on a specific study, the study is described rather than over-claimed.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
Freezing is the first stage and sets the ice structure that later becomes the pore network. The formulation is cooled below its freezing point, often with a controlled ramp, and solutes concentrate as ice forms. Primary drying then lowers chamber pressure and supplies heat to sublime the ice. The product temperature must stay below its collapse or eutectic temperature to prevent structural loss. Secondary drying raises the temperature modestly to remove bound water and achieve a low residual moisture.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | freeze-drying, lyophilisation, cryodesiccation | Lyophilization is common in pharmaceutical literature. |
| Typical chamber pressure during primary drying | 0.05–0.5 mbar (5–50 Pa) | Must remain below the triple point of water. |
| Typical shelf temperature during freezing | −40 to −20 °C | Lower temperatures may be used for eutectic systems. |
| Typical residual moisture after secondary drying | 0.5–3% w/w | Product-dependent; low moisture improves stability but can cause over-drying. |
| Typical analytical method for residual moisture | Karl Fischer titration or loss on drying | Thermogravimetric methods are also used. |
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
== Properties == nanoCLAMPs are the first antibody mimetics described to be polyol-responsive, meaning they release their targets upon exposure to a non-chaotropic salt and a polyol, such as propylene glycol. This property has been shown to be useful for purifying functional proteins and protein complexes by affinity purification. nanoCLAMPs are easily produced in the cytoplasm of E. coli, with typical yields in the range of 50 to 300 mg/L culture. Because nanoCLAMPs are devoid of cysteines, an engineered C-terminal cysteine can be used for site-directed conjugation of entities like fluorophores or resins using thiol-chemistry.
Thus, while in vitro receptor binding affinities, efficacies, and average concentrations in tissue or plasma are useful, they are not likely to predict DMT concentrations in the vesicles or at synaptic or intracellular receptors. Under these conditions, notions of receptor selectivity are moot, and it seems probable that most of the receptors identified as targets for DMT (see above) participate in producing its psychedelic effects. DMT produces the head-twitch response (HTR), a behavioral proxy of psychedelic-like effects, in rodents. However, its effects in the HTR paradigm in mice that are highly strain-dependent, including producing an HTR comparable to other psychedelics, producing an HTR that is much weaker than that of other psychedelics, or producing no HTR at all. These conflicting results may be due to rapid metabolism of DMT and/or other peculiarities of DMT in different species. Besides the HTR, DMT also substitutes for LSD and DOM in rodent drug discrimination tests. DMT has been found to increase oxytocin levels in humans. It is thought that the rate at which DMT enters the brain, and hence its route of administration, may influence its effects, with more rapid routes like intravenous administration and inhalation potentiating serotonin 5-HT2A receptor activation and consequent hallucinogenic effects. As an example, a bolus intravenous injection of 15 mg DMT produces stronger peak effects than a continuous infusion of 1 mg/minute given over 1.5 hours in spite of the latter achieving higher peak DMT levels.
==== Clay ==== The clay hypothesis was proposed by Graham Cairns-Smith in 1985. It postulates that complex organic molecules arose gradually on pre-existing, non-organic replication surfaces of silicate crystals in contact with an aqueous solution. The clay mineral montmorillonite has been shown to catalyze the polymerization of RNA in aqueous solution from nucleotide monomers, and the formation of membranes from lipids. In 1998, Hyman Hartman proposed that "the first organisms were self-replicating iron-rich clays which fixed carbon dioxide into oxalic acid and other dicarboxylic acids. This system of replicating clays and their metabolic phenotype then evolved into the sulfide rich region of the hot spring acquiring the ability to fix nitrogen. Finally phosphate was incorporated into the evolving system which allowed the synthesis of nucleotides and phospholipids."
Dye-ligand affinity chromatography is one of the Affinity chromatography techniques used for protein purification of a complex mixture. Like general chromatography, but using dyes to apply on a support matrix of a column as the stationary phase that will allow a range of proteins with similar active sites to bind to, refers to as pseudo-affinity. Synthetic dyes are used to mimic substrates or cofactors binding to the active sites of proteins which can be further enhanced to target more specific proteins. Follow with washing, the process of removing other non-target molecules, then eluting out target proteins out by changing pH or manipulate the salt concentration. The column can be reused many times due to the stability of immobilized dyes. It can carry out in a conventional way by using as a packed column, or in high-performance liquid chromatography (HPLC) column.
Sources: en.wikipedia.org
== Education and career == Schymanski graduated with a Bachelor of Science in Chemistry and a Bachelor of Engineering in Environmental Engineering from the University of Western Australia in 2003. While at the University of Western Australia, Schymanski combined chemistry and environmental engineering to study contaminated sites that required assessment and remediation. As an undergraduate, she participated in the 2002 Nobel Laureate conference which brings Nobel laureates and young scientists together; Schymanski and Pia Sappl were the first students from the University of Western Australia to receive this invitation and possibly the first Australians. After college, Schymanski spent three years at Golder Associates in Perth as an environmental engineer and then joined the Helmholtz Centre for Environmental Research in Leipzig Germany where she finished her Ph.D. in 2011. Schymanski's subsequent postdoctoral position was at the Swiss Federal Institute of Aquatic Science and Technology (Eawag) including a Marie Curie Intra-European Postdoctoral Fellowship. Schymanski is currently a Full Professor at the University of Luxembourg where she is the head of the Environmental Cheminformatics Group. In 2021, Schymanski was interviewed by the Metabolomics Society article in MetaboNews and during the interview she describes her introduction to the field of metabolomics, the current strengths of the field, and potential future applications of metabolomics research.
Ribosome profiling, or Ribo-Seq (also named ribosome footprinting), is an adaptation of a technique developed by Joan Steitz and Marilyn Kozak almost 50 years ago that Nicholas Ingolia and Jonathan Weissman adapted to work with next generation sequencing that uses specialized messenger RNA (mRNA) sequencing to determine which mRNAs are being actively translated. A related technique that can also be used to determine which mRNAs are being actively translated is the Translating Ribosome Affinity Purification (TRAP) methodology, which was developed by Nathaniel Heintz at Rockefeller University (in collaboration with Paul Greengard and Myriam Heiman). TRAP does not involve ribosome footprinting but provides cell type-specific information.
Before Roemer's time in office, Louisiana had no limits on individual campaign contributions, which allowed donors to cut massive checks to campaigns without reporting the contributions. Roemer placed Kennedy in charge of his quest to toughen campaign finance laws, including placing a $5,000 cap on individual contributions to statewide candidates. In addition to ushering in the passage of campaign finance and product liability reforms for Roemer's administration, Kennedy led the effort to consolidate Louisiana's four boards of higher education into one. He said the policy would be "fundamental" to improving Louisiana universities' "quality and desegregation". That effort eventually came one vote short of passage. Roemer lost his reelection bid in 1991, but ran again in 1995 with Kennedy as his campaign manager. Roemer later endorsed Kennedy's bids for Senate. Kennedy remained close to Roemer until his death in 2021 and credited the former governor for getting him involved in public service.
In 1977, the U. S. Navy realized that it needed a replacement for the Oerlikon 20 mm Mk 16 series of guns. In 1986, this requirement was satisfied with the introduction of the Mk 38 Mod 0 weapons system. A derivative of the M242 system, the Mk 38 consists of the M242 chain gun and the Mk 88 Mod 0 machine gun mount. It provides ships with defensive and offensive gunfire capability for the engagement of a variety of surface targets. Designed primarily as a close-range defensive measure, it provides protection against patrol boats, floating mines, and various shore-based targets.
After Rojas' deposition, the Colombian Conservative Party and the Colombian Liberal Party agreed to create the National Front, a coalition that would jointly govern the country. Under the deal, the presidency would alternate between conservatives and liberals every 4 years for 16 years; the two parties would have parity in all other elective offices. The National Front ended "La Violencia", and National Front administrations attempted to institute far-reaching social and economic reforms in cooperation with the Alliance for Progress. Despite the progress in certain sectors, many social and political problems continued, and guerrilla groups were formally created such as the FARC, the ELN and the M-19 to fight the government and political apparatus. Since the 1960s, the country has suffered from an asymmetric low-intensity armed conflict between government forces, leftist guerrilla groups and right wing paramilitaries. The conflict escalated in the 1990s, mainly in remote rural areas. Since the beginning of the armed conflict, human rights defenders have fought for the respect for human rights, despite staggering opposition. Several guerrillas' organizations decided to demobilize after peace negotiations in 1989–1994. The United States has been heavily involved in the conflict since its beginnings, when in the early 1960s the U.S. government encouraged the Colombian military to attack leftist militias in rural Colombia. This was part of the U.S. fight against communism.
Sources: en.wikipedia.org
Yes, the terms are generally interchangeable. Lyophilization is more common in pharmaceutical and laboratory contexts, while freeze-drying appears widely in food science and general writing. Both describe removal of solvent by sublimation under vacuum after freezing.
Reduced pressure keeps the process below the triple point of water, so ice can sublimate directly to vapor. It also lowers the temperature needed for drying, which helps preserve heat-sensitive materials. Without vacuum, melting or boiling could occur instead of controlled sublimation.
The rate depends on heat transfer to the product and mass transfer of vapor through the dried layer. A cold condenser, adequate vacuum, and suitable shelf temperature all influence speed. Formulation properties such as solid content and collapse temperature also set practical limits.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.